PRO Vehicle Wheel Brace KIT - Dual Size Socket
Price:
Availability:
The Pro Vehicle Wheel Brace Kit has been specially developed with easy wheel nut/bolt removal and safety as its primary purpose.
The working length has been carefully calculated for optimal torque while minimizing the amount of effort required to tighten/remove wheel nuts/bolts which allows the user to keep the shaft at a 90° angle to the wheel.
A deep socket recess fully engages on to the wheel nut/bolt head, reducing the chances of it slipping off and causing damage to the wheel surface. This is also extremely important in the removal and installation of locking wheel nut/bolts which can be problematic.
Features:
- Heat treated knuckle for maximum strength and durability
- Comfortable handle ideal for single or two-handed operation
- Well defined pommel to keep hands located and prevent them slipping
- 125mm extension bar perfect for use with deep dish wheels
- Strong storage case for all kit components so they can be safely stored in your vehicle
Supplied in a tough webbing material bag so all the parts of the kit can be kept together. Perfect for storing in the boot or under the seat of your vehicle.
Kit Contents:
1 x ½” Drive Dual Size Socket
1 x ½” (12.7mm) square drive extension bar – 125mm long
1 x Pro Vehicle Wheel Brace – 605mm long shaft
1 x Heavy duty storage case
1 x Protective gloves – Pair
1 x Instruction sheet
The Pro Vehicle Wheel Brace kit is NOT and OE part supplied by the vehicle manufacturer but the below table shows some of the compatible options for wheel nuts/bolts from the car manufacturers models.
Vehicle Hex Size Guide:
VEHICLE MANUFACTURER | HEX SIZE - Kit Required |
ALFA ROMEO | 17mm/19mm |
AUDI | 17mm/19mm |
AUSTIN | 17mm/19mm |
BENTLEY | 17mm/19mm |
BMW | 17mm/19mm |
CADILLAC | 17mm/19mm |
CHECROLET (DAEWOO) | 17mm/19mm or 21mm/22mm |
CHRYSLER/JEEP | 17mm/19mm or 21mm/22mm |
CITROEN | 17mm/19mm or 21mm/22mm |
DACIA | 17mm/19mm |
DAIHATSU | 21mm/22mm |
DODGE | 17mm/19mm |
FIAT | 17mm/19mm or 21mm/22mm |
FORD | 17mm/19mm or 21mm/22mm |
HONDA | 17mm/19mm or 21mm/22mm |
HYUNDAI | 21mm/22mm |
INFINITI | 21mm/22mm |
ISUZU | 17mm/19mm |
JAGUAR | 17mm/19mm or 21mm/22mm |
KIA | 21mm/22mm |
LADA | 17mm/19mm |
LANCIA | 17mm/19mm or 21mm/22mm |
LAND ROVER | 21mm/22mm |
LEXUS | 21mm/22mm |
LOTUS | 17mm/19mm |
MCLAREN | 17mm/19mm |
MAZDA | 17mm/19mm or 21mm/22mm |
MERCEDES BENZ | 17mm/19mm or 21mm/22mm |
MG | 17mm/19mm or 21mm/22mm |
MINI (Ford classic Mini see Rover) | 17mm/19mm |
MITSUBISHI | 21mm/22mm |
NISSAN | 17mm/19mm or 21mm/22mm |
PEUGEOT | 17mm/19mm or 21mm/22mm |
PORSCHE | 17mm/19mm |
PROTON | 21mm/22mm |
RENAULT | 17mm/19mm or 21mm/22mm |
ROVER | 17mm/19mm or 21mm/22mm |
SAAB | 17mm/19mm or 21mm/22mm |
SEAT | 17mm/19mm |
SKODA | 17mm/19mm |
SMART (Except Fortwo &ed 2008-2014) | 17mm/19mm or 21mm/22mm |
SSANGYONG | 17mm/19mm or 21mm/22mm |
SUBARU | 17mm/19mm |
SUZUKI | 17mm/19mm |
TESLA | 17mm/19mm or 21mm/22mm |
TOYOTA | 17mm/19mm or 21mm/22mm |
TVR | 17mm/19mm |
VAUXHALL | 17mm/19mm or 21mm/22mm |
VOLKSWAGEN | 17mm/19mm |
VOLVO | 17mm/19mm |
Please check your vehicle requirements by checking the owners manual or with your local dealership for the correct size needed before purchase.
Read all the instructions before using this product
- Check the socket matches the hex head size of your wheel nut or bolt.
- When using the wheel brace, ensure tht the socket is fully engaged over the head of the nut or bolt before pressure is applied.
- If you are removing a wheel always refer to the vehicle manufacturer's handbook to ensure safe removal and refitting of any wheels.
- Ensure the vehicle is parked in a safe place on firm level ground, and the handbrake is applied. Only use approved wheel jacks and wheel chocks.
- If you remove and refit any wheel fixings or the actual wheels, make sure that after the first 60 miles/100km you re-check the tightness of all wheel fixings.
Please note this kit is supplied with a dual size hex head socket. Check both sides of the socket to find the correct before attaching the wheel brace.